Відео

Very informative. But get rid of the annoying background music. It makes it difficult to listen to the instructions.

Can you install with a copper drip edge?

May i use flashing cement to stick it on the roof ?

Way wrong

U don't really need bonding adhesive. I don't think it works on pvc

what about when there is not enough room for 2 inches extra coverage. for example the edge of the roof 90* drop off. My TPO roof has cracked at the roof's side edges and made some small 1" slices where its appears the plywood edge pushes up into it from below.

what are some common products that can be used for cleaning prep and cut edge sealing? Iso alcohol and silicone respectively?

good, rush, not easy to understand, too dry.

I have a roof in CT that looks flat to the eye and is a black 10 ft seams wide material covered with a layer of pea sized rocks. It is completely drained after a rain in about 2 hours, and completely dry after 4-6 hours. What peel and stick product will work on this? Most contractors that have looked at the roof have no clue. I want to strip it down, replace any bad plywood than use a peel and stick application only, (no fumes allowed). Any advice from anyone is much appreciated. Thanks

Is there a limit in time to repair a pvc roof. I’ve been told that after 10 years it couldn’t be repaired anymore and the whole roof has to been renewed. Thanks.

This video is super weld done 😉

Where can I buy this EPDM boot? Thanks

🎉🎉🎉🎉🎉 ❤❤❤❤ love 💕

Add links to where to buy this stuff. Im going to try home depot.

Thank you so much sir

The old hand shredder plates

This is upholstery for curb 😂😂😂

@mulehide I need a rep to contact me

Gracias mañana lo intentaremos 🙏🙏🙏👌👌

Thank you

Where to buy it

Thinking on using on roof top of my Rv

Excelente explicación

When I do this, I put the seam tape on the flashing, then glue the flashing up to the tape. That way you don't need to trim at the bottom since the tape is already there with the proper exposure...

Loves this product. Always have some with me for temporary repairs.

Will this SA BaseSheet be hard to remove from plywood deck in 10 years? How do u remove it? Should it be put over the nail base first for easier removal later?

Love this

I’ve used Mule Hide for over twenty years. The silicone makes a nice looking roof that last. ABC Tampa

Nice! What are the outside corners made of?

Nothing about how to seal the seamsin the metal ? I am doing a repair right now , and every seam in the metal is leaking ! Also ,. does the metal get primer? They are doing things differently than when I went to Goodyear rubber school in Akron , in the 1980's , My supplier said the metal gets primed with the same primer as the rubber, however there is no mention of that here !

Gee commercial hack Daddy-O keep telling all what to do but never why, how else will we be as stupid as you? America Dumb Dumber and every more as stupid: Rock music these days is as bad as hippy hop.

Company that just did my roof started at the high point of the roof. Not the low. Is that a problem?

Rookie

What temperature did you have the welder set to?

My roof doesn’t have any of this. This is like 3,4 layers of protection

Where you located?

I Also use a tpo heating gun to melt the Sims for better adherence. And this is a good product when you don't want or can't do torch.

I'm installing a small, 3 square SA "Liberty" roof. The base sheet was a dream and it worked perfectly. The cap sheet is sucking. I assumed that the same method would be used on the cap sheet but I was wrong. The plastic sheet did not want to pull out easily like the base. It was a combination of the weight and the interference from the overlap area, both the plastic and the slightly rough membrane. Apparently you have to flop half of the whole length over and that will be tricky. If things don't go perfectly, it will be a shit show.

Honestly looks like shit, and when you need to bust out the caulk like that it's not gonna last. Prefer field fabricated pure tpo scuppers.

Please don't ever hand bang tpo metal unless you're doing like 2 or 3 pieces. Also, what about corners and how to dry them in??? Or tricky little wall transitions???

Do you wrap the edges, put metal on top of tpo, and cover with am adhesive membrane because it's cheaper than tpo metal? Tpo metal seems way more practical and less labor intensive, which probably costs the same in the long run as this method does. I don't get it. Unless the home owner wants a drip edge that's a certain color?

i got a pto roof i kmow that is done wrong too they took the membrane and wrap it around my drip adge and then they attach it with a metal board to my facial bored I have A lot of air pockets It looks like a white blanket on the bed This was done like two weeks ago I don’t know what to do with the roofing company if anybody have any suggestions please let me know I wish I could post some pictures of this work done

Where can you buy this at

P.s. What's your opinion on using those large 75 pound rollers to press the material down material down?

OK for a roof-over with recovery board?

🤣🤣🤣🤣🤣🤣🤣

I have this material installed on my flat roof and have an area of ponding. Is it more susceptible than other flat roof materials to damage?

They are called external corners and that is a mess, Go watch some Firestone EPDM videos.

Shouldn't you roll each roll sepratly as soon as there set not roll every roll together once you finish job

Why use two base sheets? One wasnt even fiber